3/4" (19.05cm) diameter x 30cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
3/4" (19.05cm) diameter x 38cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
- ABS bearing for use with a custom (non-stock) wheel diameter - This special bearing prevents the ECU triggering trouble codes - 25mm ID x 52mm OD x 15mm deep - Front / rear use - Used on ABS sensor side only - On the opposite side of the wheel the 513727 regular non-ABS wheel bearing is used - Tech tip. Why this bearing? On ABS equipped bikes; the ECU (on-board computer) knows what specific wheel diameter is factory installed on that bike. When installing another wheel diameter; that is custom for the specific bike; the ECU will trigger fault codes / trouble codes. Special ''ABS bearings for custom diameter wheels'' will prevent these ''different wheel diameter'' trouble/fault codes.
- ABS bearing for use with a custom (non-stock) wheel diameter - This special bearing prevents the ECU triggering trouble codes - 25mm ID x 52mm OD x 15mm deep - Front / rear use - Used on ABS sensor side only - On the opposite side of the wheel the 513727 regular non-ABS wheel bearing is used- Tech tip. Why this bearing? On ABS equipped bikes; the ECU (on-board computer) knows what specific wheel diameter is factory installed on that bike. When installing another wheel diameter; that is custom for the specific bike; the ECU will trigger fault codes / trouble codes. Special ''ABS bearings for custom diameter wheels'' will prevent these ''different wheel diameter'' trouble/fault codes.
Steel hub with metal center valve. Chrome plated 40-spoke replacement spoke wheel; laced and trued. Seals are installed; bearing spacing is pre-set and wheel is ready for installation. Wider than stock wheels are for wide tire applications. An OEM fitment may not be applicable due to OEM width restrictions in fender; belt; etc. Note: For all wire wheels it is advised to check spoke tension before installing the tire. After approx. 250km the spoke tension must be checked again to insure a correct spoke tension. After each 5000km; or as part of regular maintenance; a spoke-check is advised to insure spoke tension is still correct.
Used on inside of rim to protect inner tube from protruding spokes.
Used on inside of rim to protect inner tube from protruding spokes
Used on inside of rim to protect inner tube from protruding spokes
3/4" (19.05cm) diameter x 29cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
3/4" (19.05cm) diameter x 31cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
3/4" (19.05cm) diameter x 34.5cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
3/4" (19.05cm) diameter x 33cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
3/4" (19.05cm) diameter x 39cm long. Designed for Softail style swingarms. Comes complete with billet tip end and Allen head (socket head cap) bolt for both sides of the axle. The billet tips are special machined for Softail axle adjuster bolts. Lengths mentioned are outside swing to outside swing.
Used on inside of rim to protect inner tube from protruding spokes.
KASKI PEŁNE
KASKI OTWARTE
KURTKI MOTOCYKLOWE
SPODNIE
BUTY
RĘKAWICE